Car keys · Wychwood Park
Ignition Lock Repair in Wychwood Park
The key slides in fine and turns without any resistance at all, and the dash lights flicker, but nothing catches.
In plain words
Winters here add road grit, salt and moisture to the list of things an ignition barrel deals with, on top of ordinary wear from years of daily use. A barrel that has gone stiff or gritty through a cold, slushy season is cleaned, serviced and lubricated rather than simply forced, and the fix holds up through the next stretch of the same weather.
How the visit goesThe key slides in fine and turns without any resistance at all, and the dash lights flicker, but nothing catches. No click, no crank, just a key spinning loosely in a slot that used to grab hold of it properly.
Ignition Lock Repair
How the visit goes
Checking the other locks on the same key
Before deciding how to repin or replace the ignition cylinder, the locksmith asks about the rest of the vehicle. Do the doors and the trunk share a key with the ignition, or does one of them already need a different one? Keeping that arrangement in mind before any pinning begins means the finished repair either preserves a single working key across the vehicle or explains clearly why one lock now sits apart from the rest of them.
Clearing grit, moisture and old grease
A barrel that has gone stiff from road salt, winter grit or years of old grease is opened, cleaned and treated with whatever lubricant the vehicle's own service instructions call for. Water that has found its way into the keyway is dried out fully before the cylinder is reassembled, so trapped moisture is not left sitting against the wafers to start the same problem again next season.
Ready for the next stretch of rough weather
After a repair prompted by grit, salt or old grease, the cylinder is dried, cleaned and freshly lubricated, which carries it through a good stretch of the next season's driving. Keeping the key itself clean and dry, and avoiding a heavy keyring that drags on the barrel every time the vehicle starts, both help the repaired mechanism hold up through the weather that caused the original problem in the first place.
Ignition Lock Repair
In the van
Dry graphite or PTFE lubricant
Cylinder decoder
Key code reader
Trim clips and fasteners
Broken key extractors
Ignition Lock Repair
What affects the quote
Whether an electronic diagnosis is also needed
When the mechanical repair alone does not account for everything the vehicle is doing, checking the immobilizer or transponder side becomes a separate task, priced and scoped apart from the lock cylinder itself.
Distance to where the vehicle is
Travel is part of every visit, and a vehicle parked across town takes a different amount of driving time to reach than one nearby, which factors into how the visit gets arranged.
Weather and road conditions on the day
A barrel packed with road salt, grit or old grease from a rough season takes longer to clean and free than one that has simply worn with ordinary use over the years of driving.
What to have ready
- Are any warning or immobilizer lights showing on the dash?
- Do the doors or trunk use the same key as the ignition?
- Is any part of a key broken off inside the ignition?
Ignition Lock Repair: questions
QuestionsMy car is older and uses a plain metal key. Can the ignition still be repaired?
Yes, older mechanical ignitions are generally straightforward to service, since there is no transponder chip or immobilizer layer to work around. Worn wafers, a tired spring, or a housing that has loosened over the years are addressed directly, and a fresh key is cut from the current pinning or the vehicle's key code once the barrel itself has been sorted out.
What is actually different between ignition lock repair and dealer key programming?
The lock cylinder is mechanical: a key physically turns it through accessory, on and start. The immobilizer and transponder system is electronic: it recognises a chip inside the key before allowing the engine to run. A locksmith services or replaces the physical cylinder; programming a chip to the vehicle's electronic system is separate work that a suitably equipped automotive locksmith, a dealer, or an automotive electrical specialist can handle.
Can a key that snapped off inside the ignition be removed without damaging anything?
In most cases, yes. Hooked and spiral extraction tools reach in and draw the broken piece out along the path it entered, rather than pushing it further in. Once it is clear, the cylinder is checked for the wear that likely caused the break in the first place, and a fresh key is cut to replace both broken pieces before the vehicle is handed back to you.
Related services
- Car Key ReplacementThe fob went through the washing machine in a jacket pocket.
- Spare Car Key DuplicationThe paperwork for the used car changed hands last week, and the previous owner mentioned, almost as an afterthought, that a second key never turned up.
- Key Fob ProgrammingThe remote clicks the way it always has, but the vehicle no longer locks, unlocks or answers with its usual chirp.